Science Links Japan | Machine Design and Tribology Division Meeting in JSME

List of Jounal Titles

A to Z index of Journal Title. Choose a letter.

A/ B/ C/ D/ E/ F/ G/ H/ I/ J/ K/ L/ M/ N/ O/ P/ Q/ R/ S/ T/ U/ V/ W/ X/ Y/ Z/ 0/ 1/ 2/ 3/ 4/ 5/ 6/ 7/ 8/ 9

Machine Design and Tribology Division Meeting in JSME

1st

Traction Drive Technology. Current and Prospect.
Contribution to Development of Advanced Actuators. Actuators Using New Physical Phenomena.
Research Trend in Tribology. A Short Report from ITC Nagasaki 2000.
Development of Pivot Bearing with 2-Degrees of Freedom.
Measurement of EHL Film Thickness in Starved Condition.
Effect of Residual Stress on Surface Cracking of Cemented Carbide.
A possible mechanism for formation of steady multi-dimple in point EHL Contacts.
Design and Application Constant Axial-force Nut.
Numerical Calculation of Temperature in Bearing Clearance of Aerodynamic Three Wave bearing.
Characteristics of Aerostatic Porous Bearings with a Surface Restricted Layer using Porous Metal.
The Effect of Creep Properties of Shrink Fitter on its Mounting Performance for Optical lenses.
Friction and Wear Properties of TiO2 Ceramics.
Evaluation of wear resistance of ceramics by a solid particle impact test.
In situ observation of EHL contacts using FTIR.
Effect of Nitrogen Gas on Friction Properties in Sliding between CNx and Si3N4.
Influence of Orientation Angle on Stability of Noncircular Journal Bearings.
Equivalent meshing error at the edge of gear tooth tip.
Computer Design System of Face Gears. Geometrical Analysis of Contact Pattern.
Finish-Rolling of Gears with Shaving Machine. Measurement of Plunge Load.
Development of Evaluation System for Gear Measuring Instruments. (1st Report). Development of High Accurate Gear Measuring Instruments.
Development of Evaluation System for Gear Measuring Instruments. (2nd Report). Experimental Evaluation of Prototype Machines.
Detection of Ghost Noise on Ground Gears with Surface Measurement.
Simplified Estimation of High Frequency Gear Noise of Automobile Transmission.
Load Sharing Ratio of Crossed Helical Gears.
Quantitative Evaluation of Bending Strength of Gear Teeth based on Features of Defects.
Bending Fatigue Strength of Carburized Gear of Clean Steel.
Effect of Gear-Side Case-Hardening on Residual Stress and Bending Fatigue Strength of Case-Hardened Spur Gears.
Tooth Surface Fatigue Strength of Conical Involute Gears.
Influence of Shot Peening on Surface Durability of Case-Hardened Steel Rollers.
Evaluation of Power Transmitting Efficiency of Planetary Roller Reducer.
A Study on Virtual Texture Presentation Using a Distributed Pressure Display.
A Tactile Sensor Based on Discrete CT Algorithm.
Basic Characteristics of the Small Spherical Stepping Motor.
A Numerical Simulation for Driving Characteristics of a Multi-DOF Ultrasonic Motor.
A Micro Pump Using Peristaltic Motion with Bimorph-type PZT Elements Allay. Examination of Pumping Characteristics.
A Micromotor Using Electro-Conjugate Fluids(ECFs). Fabrication of Multi-layered Micro ECF Motors.
Development of CCD Micro Camera for In-Pipe Inspection Robot.
Development of 3-D.O.F Soft Actuator Composed of Rubber Balls.
Optimum Design of Vibrator for Linear Ultrasonic Motor based on Evaluation of Driving Characteristic using Contact Analysis.
Development of a Multi-Degree-of-Freedom Ultrasonic Motor using a Square Plate Stator.
Dynamic Characteristics of Water Hydraulic Drive System at Low Pressure Supply.
Fundamental Experiment of Electrostatic Optical Motor.
A Micropump-Mounted In-Pipe Mobile Micromachine Using Homogeneous ER Fluids.
A Microvalve Using an MRF Drop. Improvements of Flow Control Characteristics.
A Displacement Analysis of Micromanipulator for Multi Optical Switches.
Development of a micromanipulator made of diamond using a shape memory alloy actuator.
Manufacture of Dilatation Micromanipulator made of Shape Memory Polymer.
On-machine Measurement for Gear Eccentricity.
Kinematic Calibration of a Spatial Six-Degree-of-Freedom In-Parallel Actuated Mechanism Using Fourier Series.
Multi-point Positioning Control with Network-structure Robot.
Development of Brake For Robotic Use. Effect of Manufacturing Accuracy on Application Force of Brake.
Study on Shape and Stress of Links in Link Mechanism.
Degree of Freedom of Constant Velocity Joints of Automobile or a Spatialf Mechanism.
Kinematic Analysis of Spatial 7R Link Constant-Velocity Joints Extended Shaft Angle.
Ball Retaining Characteristics of Grooves of Double Offset and Cross Groove Constant Velocity Joints.