Science Links Japan | Papers of Technical Meeting on Rotating Machinery, IEE Japan

List of Jounal Titles

A to Z index of Journal Title. Choose a letter.

A/ B/ C/ D/ E/ F/ G/ H/ I/ J/ K/ L/ M/ N/ O/ P/ Q/ R/ S/ T/ U/ V/ W/ X/ Y/ Z/ 0/ 1/ 2/ 3/ 4/ 5/ 6/ 7/ 8/ 9

Papers of Technical Meeting on Rotating Machinery, IEE Japan

RM-04

27-34

The Study of Commutation Sparks and Brush Position in Universal Motors II
Examination of the armature terminal voltage of the universal motor using the LabVIEW
Characteristics of Commutation of Carbon Flat Commutator on DC Motors for Fuel Pumps
Relation between Contact Voltage drop and Ambient Temperature at Sliding Contacts
A Commutation Curve Analysis of Commutation Tester, considering Non-linear Brush Contact Characteristic.
An Improvement of Re-Impregnation Characteristics for Insulation Life Extension of Large DC Motors.
A Study on Optimal Magnetic Circuit Design of Self-start Interior Permanent Magnet Synchronous Motor
Model Elevator System Development for Student Experiment applying PLC and DC Motor Drive.
35-46
Natural Frequency Analysis of Induction Motor (K-Model of IEE, Japan) by Mechanical FEM
Analysis of Natural Frequency for Induction Motor (K Model of I.E.E.)
Radial Electromagnetic Force Analysis of Induction Motors
Development of an Electric Vehicle Using Inverter-fed Induction Motor Controlled by FPGA
Calculation of the steady state operating conditions of wind generators using induction machines
Transient Performance during Pole Change Operation of a New Prototype Six-Phase Pole Change Induction Motor for Electric Vehicles
Calculated Characteristics of A Three-Phase Squirrel-Cage Induction Motor under Unbalanced Voltage Conditions
The Study for "JEC-2137-2000 Equivalent Circuit Method"
Analysis of Equivalent Circuit of Induction Motor with Free-Rotating Magnets
Rotor bar Losses in Self Start Permanent Magnet Motor
Starting Performance Analysis for Universal Motor by FEM
Evaluation of Excitation Circuit Effects on EL CID Test by Analysis and Testing
47-61
Dynamic Characteristics Computation of Switched Reluctance Motor Based on Nonlinear Reluctance Network Analysis
The Development of Total Analysis System Using the Circuit Simulator Including Control Analysis (PSIM) by Taking Magnetic Field Analysis into Account
Modeling Approach for IPMSM based on Non-Linear Magnetization Characteristics
Basic Characteristics of Homopolar-Magnetic-Bearing-Integrated Permanent Magnet Synchronous Motor
An improvement in cogging torque of PMSM by Slot/Pole ratio
Torque Performances and Arrangement of Permanent Magnet for IPMSM
Suspension Force Characteristics and Mechanism of Suspension force generation of an Induction Bearingless Motor with a Squirrel Cage Rotor
Development of an Electric Vehicle with Outer Rotor Type Multipolar Switched Reluctance Motors
Consideration on Windage Power Loss Prediction in Design of Switched Reluctance Machines (2nd report, Experimental Evaluation of Windage Power Loss Prediction for SRM)
Simplified Non-Linear Magnetic Analysis of New Type Switched Reluctance Motor
An efficiency improvement of SRM made of laminated body of heat-treated amorphous alloys
Experimental Study of SynRM Sensorless Control Method Considering Magnetic Saturation in Cores
Influence of Magnetic Saturation on Sensorless Control for Permanent Magnet Synchronous Motors
Some Considerations on Stability of Current Polarity Detection-based Simple Position Sensorless Control for PMSM Drive
Experiment for Comparison between Two Methods of Speed Control of Permanent Magnet Vernier Motor
62-67
A new evaluation method for segmented motor core using T-shaped model
Reducing Iron Loss by Decreasing Stress in Stator Core of Permanent Magnet Synchronous Motor
Discussion of Optimum Iron Losses in Small High-Power Motors
Comparison of Magnetic Characteristics of Powder Magnetic Core and Evaluation of Motor Characteristics
A Study on Magnetic Circuit Design of Self-start Interior Permanent Magnet Synchronous Motor
Derivation of Instantaneous Torque Equations from Stator Voltages and Currents of a Permanent Magnet Synchronous Motor with Damper Winding
98-119.121-124
Smoothing Control of Wind Farm Output Fluctuation with Doubly-fed Asynchronous Machine
Calculation of the total efficiency of wind generators in steady state operation
Model Derivation of Variable Speed Wind Energy Conversion System using Permanent Magnet Synchronous Generator for analysis in terms of RMS values
Harmonic Current Analysis of Doubly-fed Generator for Wind Turbine Application Considering Winding Pattern.
A Study of Generator System Selection for Large Wind Turbine Generator System
Calculation Method for Characteristics of Permanent Magnet Generator Based on Reluctance Network Analysis
Performance Analysis of a Self-Regulated, Self-Excited, Synchronous Reluctance Generator
Genetic algorithm optimization of rotor shape for synchronous reluctance motors with concentrated winding
Maximum Efficiency Vector Control and its Performance Evaluation for Synchronous Reluctance Motor Drives
Calculation of rotational angular position from flux linkage-current characteristics of a Switched Reluctance Machine
A Sensorless Control Method of Switched Reluctance Motor Based on Self-Inductance
Speed Control of SRM Using Direct Torque Control Technique
Recent Progress on Standardization work for a Technical Report, concerning AC Rolling Mill Motors, and a Study on New Theories of Torque (E.M.F.) Constant for AC Motor, supporting Site Acceleration Test.
Experimental investigation of vibration and Noise from I.E.E. Induction Motor K Model
Finite Element Method for Natural Frequency Analysis of Stator Core in Induction Motor (K-Model)
A Study on Analysis of Inter-Bar Current of Induction Motor Using 3-D Finite Element Method
Improvement of Performance Calculation Method of Three-Phase Squirrel-Cage Induction Motors. (Third Reports)
Speed Control of Induction Motor by Using Fuzzy Logic Based On-Line Gain Tuning PI Controller
Performance Analysis of a Single-Phase Grid-Connected Permanent-Magnet Induction Generator with a Phase-Converter
Steady State Analysis of New VR Type Vernier Motors
Steady State Analysis of New HB Type Vernier Motors
Position Sensorless Control of Permanent Magnet Vernier Motor with Correction of Position Error using Estimated d-axis Current
Characteristics and future Issues of Permanent Magnet Motor
The characteristic calculating method of Permanent Magnet excited Synchronous Motor (Introduction of a JEC-TR draft standard)
Subjects of Small Sized Permanent Magnet Motors
125-150
Studies on a Wind Turbine Generator Control System using a Shaft Generator System
Simulation of transient performances of a wind power system with shaft generator system through a wind turbine simulator
Determination of field transient current of synchronous generators at asynchronizing
Studies on Improvement of Transient Performances of Self-Excited Alternating Generator Control Systems
A Basic Study on Torsional Oscillation of Turbine Generator
Measurement of Magnetic Flux Distribution in Stator Core of Small Motor Using Needle Probe Method
Position Sensorless Control of Interior Permanent Magnet Synchronous Motor
SPICE Simulation of Interior Permanent Magnet Motor Considering Nonlinear Magnetization Characteristics
Characteristics of IPMSM with consideration of field weaken control and a study of field intensify controlled IPMSM
3-D Analysis of Effects of Number of Slots on Loss in An Interior Permanent Magnet Motor
An Study of Brush Contact Voltage Drop in Collector Ring, considering Ring Materials.
Iron Losses in Turbine Generators with the Core of Grain-oriented Steel Sheets
Effect of Magnetic Anisotropy of Core Material on Motor Characteristics
Characteristics Evaluation of DC Brushless Motor Applying Amorphous Metal to a Motor Core
Circulating Current Analysis of Turbine Generator Stator Coil considering Ventilation Ducts.
Investigation of Transposition Coil and Circulating Current Loss for Turbine Generator
Optimization of Large of Roebel Transposition Coils in Turbine Generators
Evaluation of heat removal process through stator coil supports.
Turbine Generators Progress with Highly precise Analysis Design-Development of design technology and optimal generator structure by simulation-
3-D Loss Analysis of Skewed Squirrel-Cage Induction Motor Using Soft Magnetic Composites
Examination of High Power Density Pump Motor Using Powder Magnetic Core
3-D Loss Analysis of Miniature Motor by Finite Element Method
The characteristics of Hybrid Stepping Motor using powder magnetic core
Fundamental Examination of Hybrid Type Double Three-phase Stepping Motor
Technical Transition of Servo Motor and Brand New Technology
Originated as DC Power Supply, Popularized as AC Power Supply, and DC Power Supply-Era Now Again.
151-160
A Guideline for the Design of Split-Phase Start Induction Motor Fed by Inverter
Investigation of Electromagnetic Vibration Characteristics of Small Three-Phase Induction Motor
Investigation for Practical Use of .PHI.48 Small Capacitor Inducton Motor
The Study of Communication Sparks Generating in Universal Motors by DC drive
Investigation of Cogging Force in the Discontinuous Primary Linear Synchronous Motor
Modeling and Simulation of Inverter control using Current-transformers
Analysis of Rotor Eddy-Current Loss in Permanent Magnet Brushless Motors
Instantaneous torque analysis of IPMSM by a coupled simulation.
3D Eddy Current Analysis of Permanent Magnet Motors Considering Skin Effect and Grains of Electrical Steel Plate
Effect of Core Material on Reluctance Torque
161-178
A Study of An Assist Control Method of A Power Assisted Wheelchair Budi Wikaningtyas and Hisashi Takahashi
Adaptive Dead-Time Compensation scheme for Voltage Source Inverter fed Motor Drives.
Rotor Speed and Position Sensor-less Maximum Power Point Tracking Control for Wind Generation System
Trend of Control Techniques for Small Motors
High efficient control of brushless motor by optimizing phase angle and conduction angle.
Study of Open Loop Speed Control for SynRM
A study of optimal of an electric vehicles drive motor
Request of technological points for vacuum cleaner motor in 200V system
Proposal of cogging torque reduction method by the structure for brushless DC motor
High efficiency Brushless DC Motors
Fundamental Characteristics of Magnetic Gear
A simulation of bending wave vibration type ultrasonic motor adapting piezo-electric element.
The proposal of a Japanese motor industrial renewal plan
Torque Measurement Techniques
Measuring Method of the Moment of Inertia for Small Induction Motor by the Falling Method.
Recycle of Small Motor