|
List of Jounal Titles
A to Z index of Journal Title. Choose a letter.
Quarterly Journal of the Japan Welding Society
22
- Analysis by Modeling of Horizontal Coaxial Arc Welding Phenomena-Automatic Welding Process for Ship's Bottom Shell Plates-
- UV Radiation Thermometry of TIG Weld Pool-Development of UV Radiation Thermometry (Report 1)-
- High Speed Welding of Aluminium Alloy Sheets with Laser/AC Pulsed MIG Hybrid Process
- Research on Cladding and Repairing Technology Using a YAG Laser Robot system
- Formation of Photocatalyst Coating by Thermal Spraying and Effect of Additives on NOx Elimination Property
- A Predictive Formula of Weld Metal Tensile Strength
- Development of Hyper Interfacial Bonding Process for Ultra Fine-Grained Steel-Study on the Hyper Interfacial Bonding of Ultra Fine-Grained Steels (Report 1)-
- Tensile Properties and Microstructure of Weld Metal of X80 Steel by MAG Welding
- Relationship between Deterioration of Creep Rupture Strength and Microstructure in Heat Affected Zone of Heat Resistant Ferritic Steel-Modeling of Deterioration of Creep Rupture Strength in Heat Affected Zone of Heat Resistant Ferritic Steel (Report I)-
- Effect of Chromium content on Deterioration of Creep Rupture Strength and Microstructure in Heat Affected Zone of Heat Resistant Ferritic Steel-Modeling of Deterioration of Creep Rupture Strength in Heat Affected Zone of Heat Resistant Ferritic Steel (Report II)-
- Finite Element Analysis for Hot Cracking on Transverse Cross Section Using Temperature Dependent Interface Element and Quantification of Parameters Included in Proposed Method
- Detection of Phase-transformation during Welding Procedure-Application of the Laser Speckle Method to Strain Measurement in the Welding Process (Report 6)-
- Low Transformation Temperaure Materials and Welding Residurl Stress-Application of the Laser Speckle Method to Strain Measurement in the Welding Process (Report 7)-
- Weld Residual Stress and Fatigue Strength of Flanged Edge Welded Joints in Ferritic Stainless Steel
- Evaluation of Hydrogen Embrittlement Susceptibility of High Strength Steel Based on Local Approach
- Iron Casting with Mo-Alloyed and W-Alloyed for Wear Resistance and Laser Surface Modification-Laser Surface Modification of Cast Iron Aimed at Refining the Wear Resistance (Report 3)-
- Solid State Welding Aluminum Alloy to Steel Using a Rotating Pin-Solid State Welding of Dissimilar Metals Using a Rotating pin (Report 1)-
- Bonding of High Density Graphite by Brazing with Filler Metal and Sinter Bonding with Adhesive Resin using Direct Current Heating and Pressing-Study on Bonding of Carbon Materials (Report 1)-
- Bonding of Glassy Carbon Composite by Brazing with Filler Metal and Sinter Bonding with Adhesive Resin using Direct Current Heating and Pressing-Study on Bonding of Carbon Materials (Report 2)-
- Development of Flux and Filler Metal for Brazing Magnesium Alloy AZ31B
2
- Assessment of Hot Cracking Initiation by Laboratory Test Procedures and FEM-Simulation Associated Experimental Measurements During Welding of Large Weld Components
- GHTA Welding Phenomena of an Aluminum Alloy in Vacuum
- Modeling of Short-circuiting Transfer Process in GMA Welding-Numerical Model of Metal Transfer Phenomena in GMA Welding (Report 1)-
- Effect of Inner Diameter on Friction Torque in Friction Welding of Pipes
- Solutions to Problems of Tiny Spatter and Arc Interruption in AC Pulsed MIG Arc Welding
- Melting and Cutting Behavior of the Bundle of Fine Cu Wires-Study on Uniform Melting of the Bundle of Cu Wires by YAG Laser (2nd Report)-
- Observation of Bond Interface of Al/Ti Clad Material by Transmission Electron Microscopy-Development of Clad Materials by Vacuum Roll Bonding and its Characteristics (Report 4)-
- Microstructure of the Hyper Interfacial Bonded Layer of Ultra Fine-Grained Steels-Study on the Hyper Interfacial Bonding of Ultra Fine-Grained Steels (Report 2)-
- Influence of Hot Dip Galvanizing Conditions and Steel on Fatigue Strength-Fatigue Strength of Welded Joints by Hot Dip Galvanizing (Report 3)-
- Applicability of the Critical Condition for Ductile Cracking of Linepipe Steel to the Evaluation of Ductile Cracking of an Axially Notched Linepipe
- Microstructural Observation on the Bond Interface in A3003/SUS304L Clad Material-Characteristics of the Bonded Zone in A3003/SUS304L Clad Material Produced Using Vacuum Roll Bonding (Report 1)-
- Effect of Heat Treatment on the Bond Interface Structure of A3003/SUS304L Clad Material-Characteristics of the Bonded Zone in A3003/SUS304L Clad Material Produced Using Vacuum Roll Bonding (Report 2)-
- Welding between ADC 12 and SS400 by Means of Friction Stirring
- Brazability of Aluminum Alloy to Steels using Aluminum Filler Metal -Dissimilar Laser Brazing of Aluminum Alloy and Steels (Report 1)-
- Feature Extraction of Pb Free Solder Fillet Profile by an Image Processing Taking the Profile Scattering into Consideration
3
- Influence of Oxide Film on the Bondability of Aluminum in Ultrasonic Bonding and Materials Evaluation of Bonds
- Effect of Current Wave Form on AC TIG Welding for Aluminum Alloys
- Development of All Position YAG Laser Butt Welding Process with Filler Wire
- Mechanism of Fume Reduction in Welding Al-Mg Alloys Using AC Pulsed MIG Process
- Study on Phenomena of Wire Melting and Bead Formation in AC Pulsed MIG Welding
- Investigation of Effect of Substrate Heating on Transition in Flattening Behavior of Thermal Sprayed Particles
- Quality and Its Improvement of Friction Welded Joint between Rectangular Section Bar and Circular Section Bar
- Magnetostriction Stress Measurement on Dynamic Stress of Bridges and Sensitivity Calibration of Steel Used for Bridges-Applicability of Stress Measurement Technique Using Magnetostriction Effect to Welded Structures (Report 2)-
- Flashing Phenomena in Square Wave Alternating Current-Flash Welding Control by Use of PWM Inverter Power Supply (1st Report)-
- Continuous Flashing Control Using PWM Inverter-Flash Welding Control by Use of PWM Inverter Power Supply (2nd Report)-
- Resistance Heating Control with A Few Flashing Using PWM Inverter-Flash Welding Control by Use of PWM Inverter Power Supply (3rd Report)-
- Study on Galvanizing Cracks on Scallap of Steel Column Connection Joints
- Corrosion behavior of Stainless Steel Welds by Microbes in Marine Water
- The Influence of Cr in Cu-Cr Alloys on the Bondability of Diffusion Bonding of Tantalum to Cu-Cr alloys
- Characteristics of Heat-Affected Zone of Ultra-Fine Grained Steel in Ultra-Narrow Gap GMA Welding-Softening and Microstructural Consideration in Heat-Affected Zone of Ultra-Fine Grained Steel (Report 1)-
- Application to Ductile Cracking Evaluation for Beam-to-Column Connection of Steel Pier-Evaluation of Ductile Crack Initiation for Welded Structures Subjected to Large Scale Cyclic Loading (Report 2)-
- Friction Welding of Cr-Zr Copper Alloy
4
- Development of Circumferential TIG Welding Process Model-A Simulation Model for Welding of Pipe and Plate-
- NiAl Deposit Produced by PTA Surfacing Process and Its Oxidation Behavior
- NiTi Surface Layers by Plasma Transferred Arc Surfacing Process for Improving Wear Resistance of Titanium
- Effect of Beam Profile at Focal Point on Welding Deformation-Study of Deformation Behavior by Laser Welding in Micron or Sub-Micron Level in Automobile Parts (Report 2)-
- Investigation of Effective Damage Evaluation Under Repeated Prestraining of Tension and Compression in 780MPa Class High Tensile Strength Steel Plate-Studies of Safety Against Fracture on 780MPa Class High Tensile Strength Steel Plate After Prestrain (Report 3)-
- Improvement of Fatigue Strength of Aluminum Alloy Welded Joint by High Hardness and Large Specific Gravity Shot Peening
- Automatic Restraint and Visual Detection of Fatigue Crack Growth by Applying an Alumina Paste
- Effect of Creep Deformation on Stress Relaxation during Brazing Process for Electrical Ceramics-Metal Joint
- Fatigue Strength of Out-of-Plane Gusset Welded Joints with Hot Dip Aluminum Plating Coating
- Fatigue Behavior of Load-Carrying Fillet Welded Cruciform Joints with Plates of Different Thickness
- Study on Estimation Method of the Welding Deformation for Thick Plate Fillet Welding
- Laser Pressure Welding of Aluminum Alloy and Low Carbon Steel
- Diffusion Bonding of TiAl Intermetallic Compound to Ti-6Al-4V Alloy and Pure Titanium.
- Introducing Compressive Residual Stress on Metal Surfaces by Irradiating Ultrasonic Wave with a Horn in Water-Surface Modification by Irradiating Ultrasonic Wave in Liquid (Report 1)-
1
| Copyright (c) 2006-2007 Japan Science and Technology Agency. All Rights Reserved. | |
